Tuesday, June 4, 2019
Development of Magnesium-Hydrogen Peroxide Fuel Cell
Development of Magnesium-Hydrogen Peroxide fire cellPerformance of Carbon entangle cathode for MagnesiumHydrogen henry peroxide kindle mobile phonesK. Naga Mahesh, Balaji Rengarajan, K.S. Dhathathreyan*Centre for Fuel Cell Technology, International Advanced interrogation Centre for Powder Metallurgy and New Materials (ARCI), 2nd Floor, IITM Research Park, Taramani, Chennai600113.AbstractCarbon felt up and light speed stuff argon used as a cathode in Magnesium-Hydrogen peroxide provoke electric cell. The surgical process of the cathode atomic number 18 tested in a 30 cm2 area single cell assembly along with 0.68M NaCl as anolyte and 0.5M to 2M H2O2 + H2SO4 solution as catholyte. The cell was tested in polar assimilation of the reactants and at temperatures 35 to 70C. Carbon felt cathode was shown better feat than carbon cloth. The utmost current density achieved at cell voltage 1.11V was 80 mA cm-2.Keywords Mg-H2O2 kindle cell, Carbon felt, Carbon cloth, heat content peroxide,Corresponding author*Dr. K.S. Dhathathreyan,Head and Associate Director,Centre for Fuel Cell Technology,International Advanced Research Centre for Powder Metallurgy and New Materials (ARCI),2nd Floor, IITM Research Park, Taramani, Chennai600113.Ph +91446663 2723Email emailprotectedIntroductionElectrochemical systems based on Magnesium total heat peroxide raise cells (MgH2O2) have high specialized energy and are capable of converting chemical energy stored in magnesium and heat content peroxide to electrical energy 7. Recently, much attention was focused overdue to its high theoretical voltage compared to existing semi fuel cells like Aluminumsilver oxide (AlAgO) 1 or Aluminumhydrogen peroxide (Al H2O2) 2,3. The MgH2O2 fuel cell has a theoretical voltage of 4.14V which is higher(prenominal) than the resources mentioned above 4. The theoretical half cell and overall voltages for the Magnesiumhydrogen peroxide fuel cell system are as follows 5Anode Mg Mg+2 + 2e E0 = 2.37 V (vs SHE)Cathode H2O2 + 2H2 + 2e 2H2O E0 = 1.78 V (vs. SHE)Overall reaction Mg + H2O2 + 2H+ Mg+2 + 2H2O Ecell = 4.15 V (vs. SHE)The MgH2O2 fuel cells possess advantages of environmentally benign and low costs, prior to commercialization further usefulness is necessary. The cathode materials used in MgH2O2 fuel cell are the key components, which determine the consummation and stability of the cell 7. Extensive studies were carried out and explored the substrates suitable for cathodic materials and hydrogen peroxide lessening reactions 6, 8. Benette et al 9 has used fancied Micro quality carbon electrode (MCE) as cathode in AlH2O2 fuel cells, the fabricated MCE was covered by Pd/Ir clusters using a textile flocking technique. The MCE has shown a maximum power density of 90 mW cm-2 with increase loading of Pd/Ir on cathode to 10 mg cm-2. Carbon and Nickel foil substrates have been examine comparatively with Pd/Ir catalyst in MgH2O2 fuel cell. The cell voltages of 1.3V and 1.5V were obtained with nickel foil and carbon substrate catalyzed by Pd/Ir catalyst at 25 mA cm-2 10.To achieve a better performance and stability, besides a high catalytic activity of the catalyst toward the hydrogen peroxide reaction, the properties of the material for cathodic catalysts should be considered. Considering above aspects, carbon can be a good choice for its excellent corrosive resistance in different media. However, it is of challenge to prepare a carbon based substrate with both high electronic conductivity and good mechanical property 11.In the present study, carbon felt and carbon cloth has been used as cathode. The fuel cell was operated in various soaking ups of 0.2, 0.5, 1.0, 1.5 and 2M hydrogen peroxide and sulfuric venereal infection as catholyte and 0.68M NaCl as anolyte. The performance of the fuel cell in comparison with carbon cloth and Carbon felt was investigated at temperatures 35 to 70C and at flow rates 20, 50, 100 ml min-1.2. Experimental2.1 Materia lsAll materials used in this study are reagent grade quality and used as received from SRL chemicals, without further purification. All solutions are prepared in deionised water. The anode used in AZ61 magnesium alloy supplied by Omega Enterprises. The cathode used in carbon cloth and Carbon felt supplied by Nickunj Eximp Ltd.Mg-H2O2 fuel cell testsThe performance studies for carbon cloth and Carbon felt as cathode were performed in homemade Mg-H2O2 fuel cell of area 30 cm2 area single cell assembly. The active area of the electrode was 5.5 cm 5.5 cm. Nafion 117 membrane was used as a PEM membrane. The distance mingled with the membrane and electrodes is 1 mm for MgAZ61 anode as well as cathode (Carbon felt and carbon cloth). The testing of the cell was carried out by feeding different parsimoniousnesss hydrogen peroxide and sulfuric irate at cathode and 0.6M sodium chloride solution at anode. The flow rates of the mixture of hydrogen peroxide and sulfuric acid and sodium chlori de solution are supplied at 20, 50 and 100 ml min-1 by calibrated peristaltic pumps. The cell was tested at temperatures of 35, 40, 50, 60 and 70C and at 1 bar pressure. The cell temperature was controlled by plate heaters fixed to the cell.3.0 Results and Discussion3.1 Carbon felt as cathodeThe current in the cell has been increased in step wise of 0.5A and the corresponding voltages were recorded. Initially the OCV of the cell with carbon cloth as cathode is 2.04V and with Carbon felt is 2.14V. This is 2.0V lower than the theoretical voltage this whitethorn be due to the resistance of the cell materials, and mixed potential at the anode and cathode from simultaneous oxidation of H2O2 to H2O and O2 12.3.2 Effect of temperatureMg-H2O2 fuel cell is operated at temperatures 35, 40, 50, 60 and 70C. Fig. 1 represents the electrode polarization curve at different temperatures. It can be seen that the performance of the cell improved with the increase in temperatures from 3570C. At curren t density of 60 mA cm-2 the voltage was increased from 0.86V to 1.41V with increase in temperatures from 3570C. This behavior of the cell is due to step-down of hydrogen peroxide in high temperatures 6. Even though the cell performance increased, the instability in the mass transport region at higher current densities may be attributed to formation of gas bubbles due to the decomposition of hydrogen peroxide during discharge process 7.3.2 Effect of hydrogen peroxide concentration The activity of the Mg-H2O2 fuel cell increases with increasing in concentration of hydrogen peroxide. However, at high concentrations the decomposition reaction of hydrogen peroxide also occurs 6. The military group of hydrogen peroxide concentration has been investigated in concentrations of 0.5M H2O2+1.5M H2SO4 and 2M H2O2+2M H2SO4 for carbon cloth and Carbon felt. The concentrations of the catholyte have been optimized by running the fuel cell at concentrations 0.2, 0.5, 1.0, 1.5, 2M hydrogen peroxide and sulfuric acid. 0.5M H2O2+1.5M H2SO4 and 2M H2O2+2M H2SO4 have been chosen for the present study as they demonstrated good performance in comparison with others. Fig. 2 shows the performance of carbon cloth and Carbon felt at 70C with concentrations of 0.5M H2O2+1.5M H2SO4 and 2M H2O2+2M H2SO4. The increase in concentration of hydrogen peroxide and sulfuric acid improved the cell performance 7. The cathode with carbon cloth has shown maximum power density of 9.1 mW cm-2 and 6.01 mW cm-2 at 0.72V and 0.78 V and current density of 10 mA cm-2 at voltages of 0.88V and 0.55V for 2M H2O2+2M H2SO4 and 0.5M H2O2+1.5M H2SO4 concentrations, while the cathode with carbon fibre felt shown maximum power density of 91 mW cm-2 and 89 mW cm-2 at 1.3V and 1.16V and current density of 70 mA cm-2 at voltages 1.3V and 1.16 for 2M H2O2+2M H2SO4 and 0.5M H2O2+1.5M H2SO4 concentrations. The results imply that Carbon felt has performed 10 times better than carbon cloth. The reason for this effect can b e due to less contact area for cathode to perform electrochemical reduction of hydrogen peroxide on carbon cloth. In case of Carbon felt the fibrous structure provides more surface area for cathode to electrochemically reduce hydrogen peroxide 12. It can also be observed that the cathode with Carbon felt has shown better performance in the ohmic region with increase in concentration of hydrogen peroxide, later on same performance can be seen with 0.5M H2O2+1.5M H2SO4 in mass transfer region. This can be due to the 1.5 and 2M concentration of sulfuric acid. This is reasonable because electrochemical reaction of hydrogen peroxide involves H+ as reactant, the formation of H+ is rate determining step for electrochemical reaction of hydrogen peroxide, with concentrations of 1.5 and 2M H2SO4 there is really little difference in concentrations so there is a possibility of same performance in mass transfer region. It is unmingled that with the increase in concentration of hydrogen peroxid e the cell performance increased. However, the decomposition of hydrogen peroxide is also more significant as the concentration increases and can be observed during discharge of the cell. The same can be represented in Figure 2, the fluctuant curves in mass transport region portend the possible decomposition of hydrogen peroxide and production of gas bubbles that hindered mass transfer for the reactants 7.3.3 Effect of flow rateFig.3 shows the operating theatre of Mg-H2O2 fuel cell in flow rates of 20, 50 and 100 ml min-1. For both anode and cathode electrodes flow rates are kept constant. 0.6M NaCl was fed at anode and 0.5M H2O2 + 1.5M H2SO4 and 2M H2O2 + 2M H2SO4 was fed at cathode during operation of the cell. The curves have been recorded at temperature 70C. The performance of the cell shows that as the flow rate increase from 20 to 50 ml min-1 there is an improvement in performance of the cell. The flow rate was increased further 50 to 100 ml min-1 but no significance improve ment can be seen in the performance.3.4 Constant current modeThe stability test for Mg-H2O2 fuel cell with carbon felt as cathode was conducted and represented in Figure 4. The careful OCV was 2.2V and the fuel cell was operated at constant current density of 50 mA cm-2 for 300 minutes. During the constant current mode operation the voltage was 1.15V and ever decreased to 0.8V for a period of 50 minutes, during the first cycle. This is due to the consumption of Mg AZ61 anode, and was replaced with a fresh Mg AZ61 sheet for every cycle. The humps observed in the figure 4 represents cycles.ConclusionCarbon felt cathode has shown better performance in comparison with carbon cloth. Carbon felt shown a better performance with maximum power density of 91 mW cm-2 at 1.3V for 2M H2O2+2M H2SO4 which is higher than all the cathodes used and high current density of 70 mA cm-2 at voltages 1.3V and 1.16 for 2M H2O2+2M H2SO4 and 0.5M H2O2+1.5M H2SO4 concentrations which is very high in comparis on with carbon cloth.ReferencesG. Anderson, AluminumSilver Oxide Primary Battery, US Patent 3,953,239 (1976).E.G. Dow, R.R. Bessette, M.G. Medeiros, H. Meunier, G.L. Seebach, J. Van Zee, C. Marsh-Orndorff, Enhanced electrochemical performance in the development of the aluminumhydrogen peroxide semi-fuel cell, J. Power Sources 65 (1997) 207212.C. Marsh, H. Munier, R. Bessette, M.G. Medeiros, J. Van Zee, G. Seebach, US Patent 5,296,429, An Effective Method for the Reduction of H2O2.M.G. Medeiros, R. Bessette, D. Dischert, J. Cichon, US Navy Patent 6,228,527, Magnesium-Solution kind Catholyte Seawater Electrochemical System.Maria G. Medeiros, Russell R. Bessette, Craig M. Deschenes, Charles J. Patrissi, Louis G. Carreiro, Steven P. Tucker, Delmas W. Atwater, Magnesium-solution phase catholyte semi-fuel cell for undersea vehicles, Journal of Power Sources 136 (2004) 226231.Weiqian Yang, Shaohua Yang, Wei Sun, Gongquan Sun, Qin Xin, Nanostructured silver catalyzed nickel foam cathode f or an aluminumhydrogen peroxide fuel cell, Journal of Power Sources 160 (2006) 14201424.Chaozhu Shu, Erdong Wang, Luhua Jiang, Qiwen Tang, Gongquan Sun, Studies on palladium coated titanium foams cathode for MgH2O2 fuel cells, Journal of Power Sources 208 (2012) 159164.L.M. Sun, D.X. Cao, G.L. Wang, PdRu/C as the electrocatalyst for hydrogen peroxide reduction, Journal of Applied Electrochemistry 38 (2008) 14151419.C.J. Patrissi, R.R. Bessette, Y.K. Kim, C.R. Schumacher, Fabrication and Rate Performance of a Microfiber Cathode in a MgH2O2Flowing Electrolyte Semi-Fuel Cell, Journal of the Electrochemical Society 155 (2008) B558B562.M.G. Medeiros, E.G. Dow, Magnesium-solution phase catholyte seawater electrochemical system, Journal of Power Sources 80 (1999) 7882.J. Zhang, G.P. Yin, Z.B. Wang, Y.Y. Shao, Effects of MEA preparation on the performance of a direct methanol fuel cell, Journal of Power Sources 160 (2006) 10351040.C. Ponce de Leon, F.C. Walsh, A. Rose, J.B. Lakeman, D.J. Br owning, R.W. Reeve, A direct borohydrideAcid peroxide fuel cell, Journal of Power Sources 164 (2007) 441448.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment